Amplifier Power Calculator
Estimate an amplifier's electrical output power in watts from its output voltage and the connected speaker impedance, assuming a steady RMS voltage across a resistive load.
Calculators
Decision-support tools for sizing, cost, capacity, runtime, ownership, and other practical planning questions.
Estimate an amplifier's electrical output power in watts from its output voltage and the connected speaker impedance, assuming a steady RMS voltage across a resistive load.
Calculate an antenna’s ideal effective aperture from its linear gain and operating wavelength. Enter gain as a linear ratio and wavelength in meters.
Estimate the storage required for an audio file from its bitrate and duration. The calculation assumes a constant bitrate and reports decimal megabytes (1 MB = 1,000,000 bytes).
Estimate audio data size from duration, bitrate, and channel count. For uncompressed PCM audio, use the PCM-equivalent bitrate for your sample rate and bit depth. The result is an approximate decimal megabyte (MB) payload and excludes file headers, metadata, and container overhead.
Estimate one-way audio latency from buffer size, sample rate, and additional device or connection delay. This simplified estimate assumes one buffer interval and does not model every stage of an audio signal path.
Estimate potential listener reach by multiplying the listeners served per transmitter by the number of transmitters. This simple planning estimate assumes each transmitter contributes the stated audience without overlap.
Estimate the cable spools required for broadcast network runs by dividing the combined cable length by the length of one spool.
Estimate the cable-only budget for a broadcast network by multiplying the number of cable runs by the length of each run and the cost per metre.
Calculate the combined surface area of broadcast rack shelves from their width, depth, and count. This estimates shelf area in square centimeters and does not measure equipment weight capacity or rack-unit fit.
Calculate the total face area of rectangular acoustic panels in a broadcast studio by multiplying panel width, panel height, and panel count. The result is a geometric area estimate and does not determine acoustic performance or room treatment requirements.
Estimate a broadcast studio network equipment budget by adding the cost of network switches and cables. Enter quantities and unit costs in pounds sterling. This worksheet covers those equipment lines only and does not estimate installation or other project costs.
Estimate the resistance of a coaxial cable run's center conductor and return path from their combined length and resistance per meter. The estimate assumes equal conductor resistance per meter and excludes connectors and other added resistance.
Estimate monthly mobile data use from daily streaming, browsing, and voice or video calling. Enter your own typical data rates in megabytes per hour. The result is a planning estimate and does not measure your carrier account usage.
Combine sound levels in decibels by converting each level to a relative sound intensity, summing those intensities, and converting the total back to decibels. This estimates the combined level for independent sound sources measured on the same scale.
Estimate the distance at which a sound reaches a chosen decibel level, using a known sound level measured at a reference distance and an ideal free-field inverse-square model.
Estimate how long a file transfer will take from its size and the connection's sustained download speed. Uses decimal data units and assumes the entered speed is maintained throughout the transfer.
Estimate the voltage drop along a two-conductor Ethernet cable run from current, conductor resistance per meter, and one-way run length.
Estimate the ideal time to transfer a file from its size and connection speed. This model assumes a steady connection, binary file-size units, and no protocol overhead or interruptions.
Estimate the radius of the first Fresnel zone at a point along a radio link and the minimum clearance target for a chosen percentage. Uses the standard midpoint approximation with distance and frequency entered in kilometres and gigahertz.
Calculate ideal electrical power in milliwatts for a resistive load from entered RMS voltage and nominal resistance. This arithmetic estimate does not assess listening level, equipment compatibility, or hearing safety.
Calculate an Instagram post's engagement rate using likes, comments, saves, shares, and reach. The result is total recorded interactions divided by reach, expressed as a percentage.
Calculate the total number of IPv4 addresses represented by a prefix length from /1 to /32. This is the mathematical size of the address block before considering network, broadcast, or other reserved addresses.
Calculate the theoretical number of IPv6 addresses in a prefix from its prefix length.
Estimate round-trip network latency from one-way propagation, processing, and queueing delays, plus the number of network hops and per-hop forwarding delay. Enter delay values in milliseconds and hop count as a whole number. The estimate assumes each listed delay applies along the path and excludes retransmissions, packet loss recovery, and variable congestion.
Estimate an MP3 file's decimal size in megabytes from its average bitrate and audio duration. The estimate excludes metadata and container overhead.
Estimate effective network throughput from transferred data, transfer time, and protocol overhead. The result uses the same data and time units you enter.
Estimate monthly gross advertising revenue from episode downloads, available ad slots, sold inventory, CPM, and publishing frequency. This is a planning estimate before fees, taxes, or other deductions.
Estimate a podcast episode's production labor cost by multiplying recording and editing hours by a shared hourly rate. This simple estimate assumes both activities use the same rate and excludes other expenses.
Estimate the uncompressed storage required for a radio program recording from its duration, bitrate, and channel count.
Use your own inputs to calculate the result for radio studio soundproofing cost.
Estimate the radio-frequency power remaining after a transmission line using transmitter output power and a user-supplied fractional line loss. The model assumes the stated loss fraction applies to the transmitter power and excludes other system losses.
Estimate the isotropic radiated power needed to produce a specified power density at a given distance in free space, using watts per square meter and meters.
Estimate how long an audio recording will last from its file size and bitrate, using decimal megabytes and kilobits per second.
Estimate reverberation time from room volume and total equivalent sound absorption using the Sabine equation. This simplified model assumes a diffuse sound field and consistent measurement units.
Estimate the equivalent number of acoustic panels needed to cover a user-selected share of a room’s floor area. This is a material-planning worksheet, not a prediction of acoustic performance or a treatment prescription.
Estimate the fundamental axial resonant frequency along one selected room dimension using sound speed and the room dimension length.
Calculate the total pixel count and aspect ratio from a display's width and height in pixels. The pixel count is the product of the two dimensions, and the aspect ratio is shown as width to height.
Calculate the wavelength of a sound wave from its frequency and the speed of sound in the medium.
Calculate the nominal equivalent impedance of two speakers connected in parallel using their stated impedance values. This calculator covers a parallel connection only.
Estimate electrical power delivered to a speaker from voltage and nominal impedance. Choose whether the voltage is RMS or peak to make the waveform assumption explicit.
Estimate a speaker's sound pressure level at a listening position from its rated sensitivity, amplifier power, and distance. The estimate assumes free-field spreading and a single speaker.
Estimate the rack units needed for studio equipment by multiplying the device count by rack units per device, then adding spare rack units. This planning estimate assumes every device uses the same rack space and does not assess rack compatibility, weight, cooling, or cable clearance.
Calculate an engagement rate from a TikTok video's views and its likes, comments, shares, and saves. The result is total recorded interactions divided by views, expressed as a percentage.
Estimate how long a file upload will take from its size and the upload speed you enter, assuming a steady connection and decimal units.
Calculate observed service uptime as a percentage from the total monitoring period and recorded downtime. This simple ratio does not predict future reliability or account for measurement gaps.
Estimate the average video bitrate needed to fit a video within a target file size and duration. The estimate uses decimal megabytes and does not include audio or container overhead.
Estimate a video file's encoded size from its duration, video bitrate, and audio bitrate. The estimate uses decimal megabytes and assumes constant bitrates without container overhead.
Estimate decimal gigabytes of video storage from bitrate, recording duration, and recording frequency. Assumes a constant bitrate and excludes audio unless it is included in the bitrate.
Estimate the data size of an uncompressed PCM WAV recording from its duration, sample rate, bit depth, and channel count. The estimate excludes the WAV header and any metadata.
Estimate ad revenue from monetized views using your assumed revenue per 1,000 views. This is a simple planning model, not a prediction of actual YouTube earnings.